GDSD500射頻導納物位開關GDSD500RADIO FREQUENCY(RF) ADMITTANCE LEVEL CONTROLLER概述 IntroductionGDSD500系列射頻導納物位開關是一種新穎的物位測量?jī)x表，它采用先進的射頻導納技術，克服了電容式物位計不能消除導電掛料影響的缺陷，儀表具有運行可靠，適用于幾乎所有工業現場。儀表還具有安裝方便，免維護，低價位等特點, 廣泛用于石油、化工、冶金、醫藥、電力、食品、造紙等工業領域。 GDSD500series RF admittance level controller is a new level instrument.It adopts advantage RF admittance technology and overcomes the defect that capacitive level transmitter cant eliminate the influence of conductivc coating on sensor.Due to its stable operating ,it is used in almost all the industry site.With easy installing、no maintainence、low price ，the instrument is applied forpetroleum 、chemical engineering、 metallurgy 、pharmacy 、electric power、 foodstuff and paper product.結構原理 Construction Principle該物位開關由傳感器單元和電子單元組成。傳感器單元主要包括三部分：測量探極、屏蔽極及接地端。物料的高度反映為探極與容器壁間導納的變化，當物料到達開關工作點時，電子單元作出反應，驅動繼電器動作，輸出開關信號。屏蔽極可防止由于電極上有掛料而產生誤動作信號，僅當物料真正達到設置點時，繼電器才輸出信號。The controller consist of sensor and circuit .The sensor has three parts: measuring detector、 shielding detector and groundterminal.The change of admittance between detector and tank wall reflects to material height.When material height reachs controllerworking point,electric part acts to make the relay output switch signal.The shielding detector can prevent conductivc coating onsensor from error action.Only material height reachs set point really,the relay outputs the signal.參數 Parameters特點：開關控制，射頻導納原理，NULL-KOTE抗粘附電子線路。Characteristic:switch control,RF admittance principle, NULL-KOTE resist-adherence electric circuit電源：220VAC 50/60Hz 或24VDC 100mAPower: 220VAC 50/60Hz or 24VDC 100mA繼電器容量：DPDT，117/220VAC,5A無感3A有感Relay capacity: DPDT, 117/220VAC,5A non-inductive 3A inductive靈敏度：小于0.3pFSensitivity:less than 0.3pF探頭耐溫：-184+260Detector rating Temp.: -184+260電路部分耐溫：-40+80Circuit part rating Temp.: -40+80失電保護模式：采用高低模式，現場可調Fail-Safe: adopt high-low mode, adjustable at site延時可調：0-30秒Delay adjustable:0-30s防爆等級Explosion proof classification:本安型Intrinsically safe type:ExiaIICT4-CT6； 隔爆型Explosion proof typeExdIICT4-CT6型號規格表 Model & SpecGDSD500-射頻導納物位開關 RF admittance level controller224VDC供電方式Power Supply3220VACA標準靈敏度standard sensitivity電路單元靈敏度Circuit sensitivityB高靈敏度 high sensitivity0無延時(標準電路單元)no delay(standard circuit)時間延時Time delay1帶延時(0-30秒可調)delay(0-30s adjustable)Y一體式integration儀表形式Instrument typeF分體式disintergration0G1螺紋式Screw:管螺紋Pipe screw過程連接Process connecting1G1 1/42G1 1/23DN40 PN1.6法蘭式Flange4DN50 PN1.65DN80 PN1.66按客戶要求According to customers requestP普通型Normal防爆等級Explosion proof classificationD隔爆型Explosive-proofB本安型Essential-proof01標準型（溫度121）standard電極形式detector type02高溫型（溫度15m的場合Used in high/low material level length 15m circumstance82/常壓15m 4.7mm/304ss和橡膠1NPT05耐腐型proof errosion用于液體、輕漿體、顆粒（密度240kg/m3)Used for liquid、slurry、TSP121/1.38MPa457mm（18)914mm（36)9.5mm/316ss和PTFE3/4NPT備注：以上為標準長度，可根據用戶要求開關長度生產Remark:above is standard length, detail length is decided by customer外形尺寸圖 Outline dimensions接線端子圖 Wiring推薦選型安裝 Recommend Installment1）在測非導電介質時，可以為水平或垂直安裝。如需要垂直安裝時，要求探頭長至少大于控制位置6左右。 Horizontal or vertical installment is allowed for non-conductive material. If vertical installment, detector length must more than controlled point 6.2）在測導電液體、泥漿或界面檢測時，可以水平垂直安裝。探頭與物料接觸位置即報警位置。 Horizontal or vertical installment is allowed for conductive liquid slurry or interface.The position of the detector and material contacting is alarming position.3）在測粉末和顆粒裝物料時，可以水平或垂直安裝，但探頭穿過容器時，保護電極應比容器壁上的積料厚度長出2。 如用戶需要，我們可以提供材質為T(mén)eflon或Kyanr材料的防腐探頭（采用涂層法蘭連接）。 Horizontal or vertical installment for measuring fine power and particles.Pay attention:when the detector enter into the vessel, the length of the protection detector is longer 2than the thickness of particles on the vessel.If customer require,we can supply erosion-proof detector made by Teflon or Kyanr.校準 Calibrition1）靈敏度的校正Adjustment for sensitivity 當進行調節時，請注意這些總的規則： 將2個靈敏度調節電位器順時針旋轉增加靈敏度。 當兩個靈敏度控制調好后，綠色燈亮，表示探頭上“有”物料存在，紅色燈亮，表示“無”物料存在。 安裝方法有水平或垂直兩種。為保證設備穩定工作應有5分鐘預熱。 Pay attention below rules when adjusting: Add sensitivity through clockwise rotating both sensitivity resistance. After finishing adjustment,green light working shows there exist material on the detector;red light working shows no material . Two installment can be selected: horizontal & vertical.To keep 5 minutes warm-up to ensure the instrument work steadily. A）測量非導電物料，調節細（F）靈敏度控制到中間位置。然后慢慢調節粗（C）靈敏度直到狀態燈剛剛變紅。重調細（F）靈敏度控制找到一個剛剛變紅點，記下“空”的位置，如圖所示。然后，將探頭插入物料重調細（F）靈敏度控制（不接觸粗調靈敏度）剛好變?yōu)榫G點，并記下它的位置。注意兩個記號的不同，并且重調細（F）靈敏度控制到兩記號的中間位置。這就是一個完整的調試過程。To measure non-conduct material ,adjust F resistance to middle position,then adjust C resistance slowly until status light beginning to change red, repeat to adjust F to find a position which status light begins to change red,remark emptyposition; put the detector into the material, adjust F again to make the statue light change to blue,remark this position.Pay attention both different position,repeat to adjust F to between above position.All above is complete adjusting process.注意：細調可旋轉的角度應有20度，如果少于20度，請與廠家商量。建議對于非水基工藝液體（不導電液體）最好 的安裝方法是垂直安裝，當液體到達探頭10cm時報警。Remark: the rotating range of F is more than 20 degree,if less than 20,pls contact with manufacture.The best installment for non-conduct is vertical ,the controller outputs alarming signal as level reaches the detector 10cm. B）對于水基液體（導電液體）（金屬容器）：反時針調節靈敏度粗調（G）至最大，因?yàn)樗后w容易測量，只需碰到傳感探頭即可，這個過程提供最大的抗粘附能力。這是個完整的調節過程。To measure conduct material (metal vessel ): contrarotate G to max, due to measuring non-conduct easily, it is ok to only touch the detector,this process supply maximum anti-adhesion capability.This is a complete adjusting process.C)對于水基液體（導電）（非金屬容器）：參照A），但細調（F）為正好綠色位置。（有料）To measure conduct material(non-metal vessel): refer to A）,but F is in the position which status light begins to change green.2） 時間延時 Time DelayGDSD500包括0-30秒可調時間延時，有延時開/延時關模式。這種模式典型的用處是消除控制繼電器的“抖動”，或者控制循環順序。GDSD500 have 0-30s adjustable time delay and delay-open/delay-close .It can eliminate control-relay dithering or control recursive sequence. 開始時延時控制設為零（反時針到底位置）。當用延時來消除繼電器抖