1、精選優質文檔-傾情為你奉上精選優質文檔-傾情為你奉上專心-專注-專業專心-專注-專業精選優質文檔-傾情為你奉上專心-專注-專業主函數#include stm32f10 x.h#include timer.h#include led.h#include delay.h#include oled.h#include sys.hint main(void) u16 t=0; delay_init(); LED_Init(); TIM3_PWM_Init(9999,719); TIM2_Excnt_Init(10); OLED_Init(); NVIC_PriorityGroupConfig(NVIC

2、_PriorityGroup_2); OLED_ShowString(20,0,EXCNT_TEST,16); OLED_Refresh_Gram(); TIM_SetCompare2(TIM3,1000); while(1) delay_ms(1);t=TIM_GetCounter(TIM2); OLED_ShowNum(20,30,t,6,16); OLED_Refresh_Gram(); timer.c#include timer.h#include led.h#include usart.h#include oled.hvoid TIM3_PWM_Init(u16 arr,u16 ps

3、c) GPIO_InitTypeDef GPIO_InitStructure;TIM_TimeBaseInitTypeDef TIM_TimeBaseStructure;TIM_OCInitTypeDef TIM_OCInitStructure;RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM3, ENABLE); RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOB | RCC_APB2Periph_AFIO, ENABLE); /使能GPIO外設和AFIO復用功能模塊時鐘使能GPIO_PinRemapConfig(GPIO

4、_PartialRemap_TIM3, ENABLE); /Timer3部分重映射 TIM3_CH2-PB5 /用于TIM3的CH2輸出的PWM通過該LED顯示 /設置該引腳為復用輸出功能,輸出TIM3 CH2的PWM脈沖波形GPIO_InitStructure.GPIO_Pin = GPIO_Pin_5; /TIM_CH2GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP; /復用推挽輸出GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;GPIO_Init(GPIOB, &GPIO_InitStruct

5、ure);/GPIO_WriteBit(GPIOA, GPIO_Pin_7,Bit_SET); / PA7上拉TIM_TimeBaseStructure.TIM_Period = arr; /設置在下一個更新事件裝入活動的自動重裝載寄存器周期的值 80KTIM_TimeBaseStructure.TIM_Prescaler =psc; /設置用來作為TIMx時鐘頻率除數的預分頻值 不分頻TIM_TimeBaseStructure.TIM_ClockDivision = 0; /設置時鐘分割:TDTS = Tck_timTIM_TimeBaseStructure.TIM_CounterMode

6、= TIM_CounterMode_Up; /TIM向上計數模式TIM_TimeBaseInit(TIM3, &TIM_TimeBaseStructure); /根據TIM_TimeBaseInitStruct中指定的參數初始化TIMx的時間基數單位 TIM_OCInitStructure.TIM_OCMode = TIM_OCMode_PWM2; /選擇定時器模式:TIM脈沖寬度調制模式2TIM_OCInitStructure.TIM_OutputState = TIM_OutputState_Enable; /比較輸出使能TIM_OCInitStructure.TIM_Pulse = 0;

7、 /設置待裝入捕獲比較寄存器的脈沖值TIM_OCInitStructure.TIM_OCPolarity = TIM_OCPolarity_High; /輸出極性:TIM輸出比較極性高TIM_OC2Init(TIM3, &TIM_OCInitStructure); /根據TIM_OCInitStruct中指定的參數初始化外設TIMxTIM_OC2PreloadConfig(TIM3, TIM_OCPreload_Enable); /使能TIMx在CCR2上的預裝載寄存器TIM_ARRPreloadConfig(TIM3, ENABLE); /使能TIMx在ARR上的預裝載寄存器 TIM_Cmd

8、(TIM3, ENABLE); /使能TIMx外設 /定時器2外部脈沖計數函數void TIM2_Excnt_Init(u16 arr) GPIO_InitTypeDef GPIO_InitStructure;TIM_TimeBaseInitTypeDef TIM_TimeBaseStructure;NVIC_InitTypeDef NVIC_InitStructure;RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM2,ENABLE);/使能GPIOA和TIM2的時鐘RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA,EN

9、ABLE);TIM_DeInit(TIM2);GPIO_InitStructure.GPIO_Mode=GPIO_Mode_IN_FLOATING;GPIO_InitStructure.GPIO_Pin=GPIO_Pin_0;GPIO_InitStructure.GPIO_Speed=GPIO_Speed_50MHz;GPIO_Init(GPIOA, &GPIO_InitStructure);TIM_TimeBaseStructure.TIM_ClockDivision=TIM_CKD_DIV1;TIM_TimeBaseStructure.TIM_CounterMode=TIM_Counter

10、Mode_Up;TIM_TimeBaseStructure.TIM_Period=arr;TIM_TimeBaseStructure.TIM_Prescaler=0;TIM_TimeBaseInit(TIM2,&TIM_TimeBaseStructure); TIM_ETRClockMode2Config(TIM2,TIM_ExtTRGPSC_OFF,TIM_ExtTRGPolarity_NonInverted,10); /ExtTRGFilter：外部觸發濾波器。該參數取值在0 x0和0 xF之間。在我所在的環境下設置為10經檢測最準確。NVIC_InitStructure.NVIC_IRQChannel=TIM2_IRQn;NVIC_InitStructure.NVIC_IRQChannelCmd=ENABLE;NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority=1;NVIC_InitStructure.NVIC_IRQChannelSubPriority=3;NVIC_Init(&NVIC_InitStructure); /中斷優先級設置，搶占優先級為1，響應優先級為3TIM_ITConfig(TIM2,TIM_IT_Update|TIM_IT_CC1,ENABLE);/使能TIM2中斷TIM_SetCount