1、電腦每次開機總要按F2怎么辦系統遇到開機故障問題屬于常見問題之一,相信很多用戶都有 遇到過,比如電腦每次開機總要按F2才能進入系統,那么你知道電 腦每次開機總要按F2怎么辦嗎?下面是小編整理的一些關于電腦每 次開機總要按F2的相關資料，供你參考。電腦每次開機總要按F2的解決方法一:1、電腦沒有安裝軟驅或者軟驅故障,而在BIOS里卻設置有軟 驅,這種情況會導致F2提示；2、大部分情況下只需要恢復BIOS的默認設置即可恢復正常; Colorful Magic ControlLoad Fail-Safe Defaults lures9Load OptiMized Defaults 1Is«

2、pwiSet Supervisor PasswordSet User PasswordSave t Exit Setup3、某些比較舊的主板默認設置也會開啟軟驅,這時進入BIOS 后請選擇第項"Standard CMOS Features0 ; Standard CMOS Features> 卜equenc“UolMge Control Advanced BIOS FeaturesLoad Failsafe Defaults> Advanced Chipset FeatiresLoad Optimized Defaults Intcsrled Per iphera1>

3、;Set Supervisor Password Power Management SetupSet User Password PnP/PtI ConfigurationsSave & Exit Setup卜 PC Health St at u<Fxit Without Sluing4、進入后將"Drive A"設置為"None" z "Floppy 3 ModeSupport"設置為"Disable"CWW IHlIlty cyrlfbt (C)SUaiaH OQS reaUmBate(Hi：44

4、：yy)Z my 1 2M9l<- *|Tlae (Ni：m：ss)10 ： 21 ： 39Rm Lewi > 1 lit OmsmI IlMUr(ST3Z5I31M1> IK CteMel Sl«w(UKOiaabMI(lit ClMBael i Rttter(somr M-m milHorm ri«m M* 1H CImbmI 1 SlaveimimmusiJIBriw Alrlvc lblH klw Flom 3 Mt SappoK(IMWIl4e CfKtiMItalt ObMil Bit UyboaNlL_5、返回 BIOS 設置主界面,選擇&q

5、uot;Advanced BIOS Features0 設置項,按回車鍵進入；CHU ttetup Utility - CoiMM iflht (O lHb-ZUU4> Ruerican Hegatreirfs. J Staiwlarcl BIOS Features BIOS Security Features Mvanced BIOS Faat«iresLLoad Optima) Defaults Adum:ed Chipset FeaturesLoad FaiIsafe Defaults PCI/PNP Resource NanageaentDiscard Changes

6、Boot Configuration FeaturesSave Changes and Exit Power Hanagetteni FeaturesDiscarti Chanves and Exit6、將"Boot Up Floppy Seek"設置為"Disabled"ncrnOVaDic vuviuu iriuriLy 11 1 uii ter j(Press Enter Press Enter) PCI SlotMenUirus UarningFirst Boot Device Second Boot Devic Third Boot Deuic

7、e Boot Other DeviceBoot Up Floppy SeekDisabled (Enabled ( JHard Disk Boot Priority CD-ROM Boot Priority Init Display First7、按F10保存z ESC鍵退出BIOS設置，重新啟動電腦即可。 CM Z" 47 am FeHmi let皿 BMafaiBM Ma.T hlFUU Mwlti1 ”Malt*X SvriMr htwttfX tar Fmari1 , K tMlia SUH*-Itv aw on iwr ir電腦每次開機總要按F2的解決方法二:1、主板上有一

8、塊紐扣電池來維持電腦在沒有電源接通的情況 下保存BIOS設置及繼續主板時鐘的運行,如果這塊紐扣電池沒有電 了也會導致這種情況。這時,首先需要斷開電腦主機的電源線，打開 電腦機箱；62、找到主板上的紐扣電池;3、使用一字螺絲刀將電池撬下來;6“亦討耶MJHl圧BIOS、刪竄DI畧冊w。 MB Intelligent Iwedkur(M.II.)Load Fail-Safe Defan its Standard CMOS FeaturesLoad UpLinized Defaults Advanced BIOS FeaturesSet Supervisor Password丨毗ugratRd Pe

9、ripheralsSet User Password電腦每次開機總要按F2的解決方法三:1、如果電腦有雙硬盤或多塊硬盤，或者光區,當直接從電腦中拔掉了硬盤或光驅卸載以后,BIOS中的設置沒有更新；2、現在的電腦主板一般都有硬盤光驅自動檢測功能，進入BIOS 設置 z 選擇"Standard CMOS Features"CMOS Setup Utility - Copyright (:C) 1984*2801 Award Software Standard CHDS FeaturesLoad Fail-Safe Defaults Advanced BIOS FeaturesL

10、oad Optinized Defaults Advanced Chipset FeaturesSet Supervisor Password Integrated PeripheralsSet User Password Pouer Nanagenent SetupSave 1 Exit Setup PnP/PCl Conf igurat ionsExit Without Sawing Frequency/Uoltage ControlEsc : Quitt A 4 : Select ItenFIB : Save 1 Exit Setup3、將硬盤和光驅都設置為自動檢測即可。Standard CMOSFeaturesDate(HH：DD：YY):(Thu 05/13/2010TiMe(HH：HH：SS):(13:35:201 IDE Prinary Haster(PIONEER DUD-ROJ IDE Pr ftiaary Slaue(ST380011A SATAI(UDC UD8088AADSJ SRTA2(BENQ DUDROH DDJ SATA3Not Detected SATM(Not Detec