骨架參數-->,,最小直徑(mm),最大外徑(mm),骨架槽寬(mm),★使用前請注意最下方的備注,,,,,,,,,,

,,12.10,20.50,21.70,,,,,,,,,,,

,,上擋墻寬(mm),下擋墻寬(mm),繞線寬度(mm),,,,,,,,,,,

,,,,25.80,,,,,,,,,,,

繞組1,線徑(mm),匝數(Ts),線頭長度(mm),膠帶層數,膠帶長度（m）,銅線長度（m）,銅線重量（g）,線包狀況,,,,,,,

,0.45,44,100.00,3.00,137.95,1.835,2.60,OK,,,,,,,

,輔助參數,13.306,,1,,,,,,,23.64,,,,

繞組2,線徑(mm),匝數(Ts),線頭長度(mm),1.00,膠帶長度（m）,銅線長度（m）,銅線重量（g）,線包狀況,,,,,,,

,0.65,33,150.00,2.00,116.51,1.665,4.92,OK,,,0.45,0.16,,,

,輔助參數,16.125,,2,,,,,,,0.5,0.185,,,

繞組3,線徑(mm),匝數(Ts),線頭長度(mm),1.00,膠帶長度（m）,銅線長度（m）,銅線重量（g）,線包狀況,,,1.46,,,,

,0.45,8,50.00,3.00,179.67,0.467,0.66,OK,,,1059.67,,,,

,輔助參數,17.331,,1,,,,,,,,,,,

繞組4,線徑(mm),匝數(Ts),線頭長度(mm),膠帶層數,膠帶長度（m）,銅線長度（m）,銅線重量（g）,線包狀況,,,銅線,重量,單價,金額,

,0.65,33,150.00,3.00,196.36,2.015,5.95,OK,,,0.45,7.19,0.063,0.45297,

,輔助參數,18.940,,1,,,,,,,絕緣線,線長,,,

繞組5,線徑(mm),匝數(Ts),線頭長度(mm),膠帶層數,膠帶長度（m）,銅線長度（m）,銅線重量（g）,線包狀況,,,0.45,3680,0.17,0.6256,

,0.45,44,100.00,3.00,208.86,2.781,3.93,OK,,,膠帶,長度,,,

,輔助參數,20.146,,1,,,,,,,22,850,0.19,0.053833333,

繞組6,線徑(mm),匝數(Ts),線頭長度(mm),膠帶層數,膠帶長度（m）,銅線長度（m）,銅線重量（g）,線包狀況,,,b/n,ER28/34,0.18,0.18,

,0.40,5,50.00,3.00,220.32,0.373,0.42,線包胖啦！,,,core,ER28/34,0.02,0.66,

,輔助參數,21.252,,1,,,,,,,人工,,,0.6,

繞組7,線徑(mm),匝數(Ts),線頭長度(mm),膠帶層數,膠帶長度（m）,銅線長度（m）,銅線重量（g）,線包狀況,,,,,,2.572403333,3.972819708

,0.20,22,100.00,1.00,88.85,1.583,0.44,線包胖啦！,,,,,,,

,輔助參數,21.755,,1,,,,,,,,,,,

繞組8,線徑(mm),匝數(Ts),線頭長度(mm),膠帶層數,膠帶長度（m）,銅線長度（m）,銅線重量（g）,線包狀況,,,,,,,

,0.45,30,50.00,3.00,238.04,2.143,3.03,線包胖啦！,,,,,,,

,輔助參數,22.961,,1,,,,,,,,,,,

繞組9,線徑(mm),匝數(Ts),線頭長度(mm),膠帶層數,膠帶長度（m）,銅線長度（m）,銅線重量（g）,線包狀況,,,,,,,

,0.20,38,50.00,1.00,95.83,2.815,0.79,線包胖啦！,,,,,,,

,輔助參數,23.464,,1,,,,,,,,,,,

繞組10,線徑(mm),匝數(Ts),線頭長度(mm),膠帶層數,膠帶長度（m）,銅線長度（m）,銅線重量（g）,線包狀況,,,,,,,

,,,,,22.11,0.000,0.00,線包胖啦！,,,,,,,

,輔助參數,23.464,,1,,,,,,,,,,,

,,,,,,,,,,,,,,,,

備注：1.表中藍色部分為輸入數據區，必須輸入才能計算結果，,,,,,,,,,,,,,,,

2.表中白色及紫色部分為計算結果區域，不得輸入數據和隨意修改！,,,,,,,,,,,,,,,

3.如果是多股線，可以用股數×圈數作為總圈數，然后線徑按單股線算；,,,,,,,,,,,,,,,

4.三重絕緣線的線徑計算時按：線徑+0.2mm，切記！,,,,,,,,,,,,,