單片機原理及應用技術項目三數碼管顯示的溫度計設計任務2多位LED數碼管顯示設計學校名稱：平頂山工業職業技術學院主講人：高同輝技能點編程實現多位共陰極數碼管動態顯示任務實施四授課內容1.硬件電路接線2.軟件程序編寫3.編譯、下載、驗證4.結果分析評價與反饋五四、任務實施

1.硬件電路接線

數碼管的A,B,C,D,E,F,G,DP引腳分別接入開發板的數字管腳2，3，4，5，6，7，8，9。數碼管公共端1，2，3，4引腳通過串聯220Ω限流電阻依次接數字管腳10,

11,

12,

13。四、任務實施

2.軟件程序編寫#defineSEG_A2#defineSEG_B3#defineSEG_C4#defineSEG_D5#defineSEG_E6#defineSEG_F7#defineSEG_G8#defineSEG_H9#defineCOM110#defineCOM211#defineCOM312#defineCOM413unsignedchartable[10][8]={{0,0,1,1,1,1,1,1},//0{0,0,0,0,0,1,1,0},//1{0,1,0,1,1,0,1,1},//2{0,1,0,0,1,1,1,1},//3{0,1,1,0,0,1,1,0},//4{0,1,1,0,1,1,0,1},//5{0,1,1,1,1,1,0,1},//6{0,0,0,0,0,1,1,1},//7{0,1,1,1,1,1,1,1},//8{0,1,1,0,1,1,1,1}//9};voidsetup(){for(inti=2;i<14;i++){pinMode(i,OUTPUT);}}四、任務實施

2.軟件程序編寫case4:digitalWrite(COM1,HIGH);digitalWrite(COM2,HIGH);digitalWrite(COM3,HIGH);digitalWrite(COM4,LOW);//選擇位4break;default:break;}//a查詢碼值表digitalWrite(SEG_A,table[num][7]);digitalWrite(SEG_B,table[num][6]);digitalWrite(SEG_C,table[num][5]);digitalWrite(SEG_D,table[num][4]);digitalWrite(SEG_E,table[num][3]);digitalWrite(SEG_F,table[num][2]);digitalWrite(SEG_G,table[num][1]);digitalWrite(SEG_H,table[num][0]);}voidloop(){

Display(1,1);//第1位顯示1delay(500);Display(2,2);//第2位顯示2delay(500);Display(3,3);//第3位顯示3delay(500);Display(4,4);//第4位顯示4delay(500);}switch(com)//選通位選{case1:digitalWrite(COM1,LOW);//選擇位1digitalWrite(COM2,HIGH);digitalWrite(COM3,HIGH);digitalWrite(COM4,HIGH);break;case2:digitalWrite(COM1,HIGH);digitalWrite(COM2,LOW);//選擇位2digitalWrite(COM3,HIGH);digitalWrite(COM4,HIGH);break;case3:digitalWrite(COM1,HIGH);digitalWrite(COM2,HIGH);digitalWrite(COM3,LOW);//選擇位3digitalWrite(COM4,HIGH);break;voidDisplay(unsignedcharcom,unsignedcharnum){for(intj=2;j<10;j++){digitalWrite(j,LOW);}四、任務實施3.編譯、下載、驗證觀察現象：數碼管從0開始累加顯示數據。

程序中根據實驗原理圖，通過數碼管庫函數進行數碼管初始化，不斷對numToShow變量進行累加，然后對數碼管進行設置數據、刷新顯示的操作。程序中沒有使用delay()函數進行延時，而是通過不斷累加delaycount變量，在其達到理想閾值時對numToShow變量進行累加。因?yàn)閿?shù)碼管需要不斷重復刷新數據才能保持顯示，若使用delay()進行延時，則程序?qū)⑼Ｖ惯M(jìn)行等待，這段時間數碼管得不到刷新，顯示就會受到影響，數碼管會變暗、閃爍甚至熄滅。更加理想的做法是通過定時器來對數碼管進行刷新。4.結果分析五、評價與反饋多位數碼管顯示編程思路：打開